Low value craft kitchen cornice

Through: Annabelle Keller for STYROFOAM™ Logo Foam

Here is a a laugh, affordable, no‐stitch makeover for any window in your house. Merely glue batting and upholstery to cornice sections reduce from foam sheets. How flexible!

Fabrics:
• STYROFOAM Logo Foam:
o Sheets, 36″ x 12″ x 1″, two
• Cotton print materials, 45″ broad, 2 yds. each and every: pillow panel (eight” tall motif); coordinating important points
• Unbleached muslin, 90″ large, three/four yd.
• Duvet batting, crib measurement or 45″ broad, 1‐five/eight yds.
• Iron‐on adhesive: 17″ x 1‐five/eight yds.; three/eight” and seven/eight” large, one package deal each and every
• Grosgrain ribbon to compare materials, three‐1/eight yds. each and every: colour A, three/eight” and seven/eight” widths; colour B, three/eight”
• Floral provides: t‐pins, six; picket choices with wires got rid of, three” lengthy, 35
• Attitude brackets with screws, five”, two
• Serrated knife
• Candle stub or paraffin
• Fantastic‐line black everlasting marker
• Yardstick or ruler
• Scissors
• Immediately pins
• Iron and ironing board
• Low‐temp glue gun and glue sticks
• Glue for plastic foam

For trend :

Steps:

1. Wash and dry materials with out material softener; press.

2. Discuss with slicing format to attract cornice sections onto one foam sheet; label sections. Wax serrated knife with candle stub or paraffin. Minimize sections from foam.

three. Use glue gun to attach 3 floral selections, similarly spaced, midway into brief finish of 1 TOP. Practice foam glue to foam edge round selections. Use glue gun to attach sticking out pick out ends into brief finish of final TOP, so sections have compatibility tightly in combination. Completed cornice most sensible will have to measure five” x 38″.

four. Check with Fig. 1 to sign up for facets to most sensible. Use glue gun to attach 3 selections into each and every brief finish of cornice most sensible, leaving three/four” pick out finish sticking out from foam. Practice foam glue to foam edge. Use glue gun to use glue to sticking out pick out ends. Press higher five” edges of ENDS flush with cornice most sensible as proven. Most sensible of cornice will have to measure five” x 40″.

five. Repeat Step three to sign up for FRONT to last foam sheet alongside one 12″ edge. Seek advice from Fig. 2; selections are indicated through brief black strains. Completed cornice entrance will have to measure 12″ x 40″.

6. Use glue gun to attach last choices midway into entrance fringe of most sensible/facets meeting, spacing choices about three” aside. Follow foam glue to foam edge round selections. Gently press cornice entrance onto pick out guidelines. The use of glue gun, spot glue foam edges between choices. Temporarily and firmly press cornice entrance flush with cornice most sensible/facets meeting. Let dry utterly.

7. Minimize one 23″ x 57″ rectangle from batting. Middle cornice entrance on batting. Clean batting over out of doors of cornice, permitting extra to overlap backside and again edges (the place cornice will relaxation towards wall). Pin batting to out of doors of cornice to safe. Wrap batting easily round cornice edges to inside of, trimming and mitering corners as wanted. Pin to safe. Trim extra batting, permitting 1‐1/2″ overlap inside of each and every edge. Use glue gun to safe batting to inside cornice. Let dry utterly. Take away pins.

eight. Minimize one 23‐1/2″ x 57‐half” rectangle from muslin. Repeat Step 7, gluing muslin over batting.

nine. Reduce one each and every from small‐print material for cornice lining: five‐1/2″ x 60″ (inside of most sensible and facets); 11‐half” x 39″ (inside of entrance). Press 1/2″ hem in each brief and one lengthy fringe of 60″ material piece. With material proper aspect out, pin lengthy hemmed edge inside of cornice, three/four” from again open edge. Use glue gun to attach material to inside muslin‐coated cornice. Take away pins. Clean lining with palms. Press 1/2″ hem in both sides of entrance lining piece. Use glue gun to attach material, proper aspect out, to inside of cornice entrance, overlaying uncooked fringe of most sensible/aspect lining.

10. Reduce vertical row of panels from pillow panel material. The use of photograph as information, middle material over cornice entrance and facets; pin to safe.
Minimize two material strips for most sensible and backside borders if wanted, each and every roughly three” x 56″. Pin borders to entrance and facets of cornice.

11. Minimize ribbon lengths to suit and place as desired alongside most sensible and backside panel and cornice edges, hiding uncooked material edges, and round panel motifs. Pin to safe. Notice: Style pictured makes use of vast inexperienced ribbon, slender inexperienced ribbon, and slender purple ribbon to enrich materials. For higher and decrease panel borders, middle slender ribbon over vast ribbon as proven.

12. When proud of association, in moderation switch material items and ribbon to paintings floor. Following producer’s directions, practice iron‐on adhesive to flawed aspect of material and ribbon lengths. Starting with panel, take away paper backing from material and iron directly to cornice. Trim extra duration and notice glue to again fringe of cornice. Repeat for borders and ribbon lengths.

13. Apply producer’s directions to glue brackets to most sensible again edges of cornice.

®™ Trademark of The Dow Chemical Corporate (“Dow”) or an affiliated corporate of Dow. For extra venture concepts, please see styrofoamstyle.com.
®™ Trademark of The Dow Chemical Corporate (“Dow”) or an affiliated corporate of Dow. For extra venture concepts, please see styrofoamstyle.com.